Post by Russ on Oct 14, 2012 9:50:19 GMT -5
YOUTH RULES
This class is for the kids AGES 12-16 W/0 DRIVERS LICENSE let them learn how to strip cars out, build a car to the rules and be a good sport when they win or lose.
Upon arrival a notarized parental consent form must be filled out or you will not be allowed to participate. One parent must be present with valid I.D. A notary will be present to notarize the entry forms. A PARENT OR ADULT MUST RIDE WITH THE DRIVER. this is for instructional purposes as well as a possible emergency situation .
BUILDING** all cars must remain stock unless specified in these rules NO TUCKING/WEDGING
all cars must be factory front wheel drive 4 or 6 cylinder and wheelbase must not exceed 109"
strip interior100%! u can leave in passenger seat, dash , KEY START RECOMMENDED remove airbags!
WELDING** One bar behind seat 12 x 12 inner door plates and No larger than 6" dia. pipe. A roll over bar strongly advised. You may have a 4 point cage for driver and pass. safety. reinforcing the drivers door and passenger door highly recommended.
DOORS/ TRUNK/TAILGATES outside only 3"wide x1/4 thick strapping.......... both outside front doors can be reinforced 6 inches past the door seams. so do it!
BUMPERS** 80 and newer bumpers allowed, they must be bolted on at the factory location, WITH 8 ....1/2 bolts 2" washers max size you can wire your bumpers to the trunk lid 2 places and the radiator support in 2 places with #9 wire. THERE CAN BE 12 " OF WELD ON EACH BUMPER . THIS MEANS ON THE MOUNTING AREA YOU CAN HAVE A 3" LONG BEAD OF WELD IN 4 SELECTED LOCATIONS.
TIRES** No studded tires on the front. You can glue, screw, double and stem protection is allowed. remove wheel weights any tire permitted.
WINDSHIELD** Must be removed. Must have 2 places of #9 wire, banding, strapping or chain in windshield area to protect driver/pass. Mount this from roof to the cowl panel. It must not be attached to the hood
BATTERY** Must be mounted inside the car , all parts of battery must be covered with a non flammable material.
HOODS** Can be secured in 6 places. 2 strand #9 wire, banding or chain
Fuel Tanks***This is the most important rule to read. Any fuel system I feel that’s unsafe will not pass.
Stock fuel tanks can be left in if they are mounted in front of rear axle. I don’t want to see a stock tank mounted in your back seat area. Tanks must be made of steel a 4 point hold down bolted to floor with a minimum of a 2" washer on the underside of car. All hoses must be double clamped at all connections. Electric fuel pumps must be operated by a switch that the passenger can shut off in case of a fire. I'll paint switch during inspection. Stock systems will simply use the key.
This class is for the kids AGES 12-16 W/0 DRIVERS LICENSE let them learn how to strip cars out, build a car to the rules and be a good sport when they win or lose.
Upon arrival a notarized parental consent form must be filled out or you will not be allowed to participate. One parent must be present with valid I.D. A notary will be present to notarize the entry forms. A PARENT OR ADULT MUST RIDE WITH THE DRIVER. this is for instructional purposes as well as a possible emergency situation .
BUILDING** all cars must remain stock unless specified in these rules NO TUCKING/WEDGING
all cars must be factory front wheel drive 4 or 6 cylinder and wheelbase must not exceed 109"
strip interior100%! u can leave in passenger seat, dash , KEY START RECOMMENDED remove airbags!
WELDING** One bar behind seat 12 x 12 inner door plates and No larger than 6" dia. pipe. A roll over bar strongly advised. You may have a 4 point cage for driver and pass. safety. reinforcing the drivers door and passenger door highly recommended.
DOORS/ TRUNK/TAILGATES outside only 3"wide x1/4 thick strapping.......... both outside front doors can be reinforced 6 inches past the door seams. so do it!
BUMPERS** 80 and newer bumpers allowed, they must be bolted on at the factory location, WITH 8 ....1/2 bolts 2" washers max size you can wire your bumpers to the trunk lid 2 places and the radiator support in 2 places with #9 wire. THERE CAN BE 12 " OF WELD ON EACH BUMPER . THIS MEANS ON THE MOUNTING AREA YOU CAN HAVE A 3" LONG BEAD OF WELD IN 4 SELECTED LOCATIONS.
TIRES** No studded tires on the front. You can glue, screw, double and stem protection is allowed. remove wheel weights any tire permitted.
WINDSHIELD** Must be removed. Must have 2 places of #9 wire, banding, strapping or chain in windshield area to protect driver/pass. Mount this from roof to the cowl panel. It must not be attached to the hood
BATTERY** Must be mounted inside the car , all parts of battery must be covered with a non flammable material.
HOODS** Can be secured in 6 places. 2 strand #9 wire, banding or chain
Fuel Tanks***This is the most important rule to read. Any fuel system I feel that’s unsafe will not pass.
Stock fuel tanks can be left in if they are mounted in front of rear axle. I don’t want to see a stock tank mounted in your back seat area. Tanks must be made of steel a 4 point hold down bolted to floor with a minimum of a 2" washer on the underside of car. All hoses must be double clamped at all connections. Electric fuel pumps must be operated by a switch that the passenger can shut off in case of a fire. I'll paint switch during inspection. Stock systems will simply use the key.