Post by Russ on Oct 14, 2012 9:51:53 GMT -5
80 & NEWER WIRE UP CLASS
1. Any American-made sedan or station wagon 1980 and newer 2. Helmet, seat belt, and eye protection must be worn at all times. Long sleeves and Long pants required.
3. Any controversies or protests must be brought up during the drivers meeting.
4. Any questions call first. If it doesn't say you can don't do it. Cars must be stock. No painting of the frames. If the car is black it must have a 12" x 12" roof sign.
5. Judges decision's are final. All cars are subject to re-inspection at any time before, during, or after the event.
6. All glass, plastic, and interior must be removed before arriving to the event.
7. Any car motor of choice is permitted. NO DISTRIBUTOR PROTECTORS. NO ENGINE CRADELS. NO MOTOR PROTECTOR. NO KICKERS. MUST USE STOCK MOUNTS. Can have ONE chain per side, going down TWO length welded 3/8 chain to cradle under engine not the frame.
8. Trailer hitches and braces must be removed.
9. A 14" x 14" inspection hole must be put in all deck lids. Deck lids MUST be in original position. NO WEDGING. Some body creasing is ok. Drivers Door may be welded solid outside seam only. All other doors must be wired shut.
10. Original gas tank must be removed and replaced with a boat-type tank or fuel cell. Moved inside of car behind driver's seat but no further back than rear axle. Batteries must be moved to passenger side floor board and securely fastened.
11. No interior seam welding will be permitted. Repairing sheet metal is limited to where the battery box and gas tank and drivers area of the floor boards of the car.
12. NO FRAME WELDING. You may weld the bumper and bumper shock there must be at least a 1“ gap between bumper and frame if using a factory bumper shock. Bumper may be welded directly to frame but the bumper shock must be removed completely. No adding metal. .1980 and NEWER bumpers only will be permitted. No tilting OR COLD BENDING of frames will be permitted
13. Hood- wire ONLY. 8 double strand of #9 wire 2 may go around bumper and or frame. Hoods must be open for inspection. (12" x 12" hole over carburetor). Deck lids may be wired same way no welding permitted.
14. Angles for cross member can't be longer than 5" and must be within 12" from factory location.
15. Tie Rods MAY BE REINFORCED No gas tank protectors.
16. Factory body bolts may be changed to ½” bolts you must use factory rubber and bushing spacer and there must be a 1 “ gap between body and frame. YOU MAY HAVE A BAR IN DASH AREA AND ONE BEHIND SEAT SHEET MEATAL TO SHEET METAL ONLY AND CAN NOT STENGTHEN CAR IN ANY WAY.
17. Rear coil springs may be wired or chained. No solid suspensions. All suspension components must remain factory stock. No modifications will be permitted. Cars must bounce.
18. Front coil springs must remain stock. You can use screw-in spacers. Leaf spring cars must remain factory springs. NO EXCEPTIONS! You cannot change coil spring to leaf spring set ups.
19. Car must set level bumpers can not be higher than 18” to bottom of bumper
20. Any stock 5 bolt rear end permitted. No rear end protectors. Must use STOCK trailing arms.
21. Cars must be stock.
22. WE HAVE THE RIGHT TO RE-INSPECT, CUT, OR DRILL ANY CAR AT ANY TIME. IF YOU ARE CAUGHT BREAKING THE RULES SET HERE FORTH YOU WILL FORFIET ANY AND ALL WINNINGS AND OR PRIZES YOU ARE DUE. .
23. NO OTHER MODIFICATIONS MAY BE MADE TO CAR UNLESS THEY ARE STATED IN THE RULES ABOVE IF YOU STRETCH A RULE YOU WILL LOSE THAT RULE.NO WELDS ON FRAME!
1. Any American-made sedan or station wagon 1980 and newer 2. Helmet, seat belt, and eye protection must be worn at all times. Long sleeves and Long pants required.
3. Any controversies or protests must be brought up during the drivers meeting.
4. Any questions call first. If it doesn't say you can don't do it. Cars must be stock. No painting of the frames. If the car is black it must have a 12" x 12" roof sign.
5. Judges decision's are final. All cars are subject to re-inspection at any time before, during, or after the event.
6. All glass, plastic, and interior must be removed before arriving to the event.
7. Any car motor of choice is permitted. NO DISTRIBUTOR PROTECTORS. NO ENGINE CRADELS. NO MOTOR PROTECTOR. NO KICKERS. MUST USE STOCK MOUNTS. Can have ONE chain per side, going down TWO length welded 3/8 chain to cradle under engine not the frame.
8. Trailer hitches and braces must be removed.
9. A 14" x 14" inspection hole must be put in all deck lids. Deck lids MUST be in original position. NO WEDGING. Some body creasing is ok. Drivers Door may be welded solid outside seam only. All other doors must be wired shut.
10. Original gas tank must be removed and replaced with a boat-type tank or fuel cell. Moved inside of car behind driver's seat but no further back than rear axle. Batteries must be moved to passenger side floor board and securely fastened.
11. No interior seam welding will be permitted. Repairing sheet metal is limited to where the battery box and gas tank and drivers area of the floor boards of the car.
12. NO FRAME WELDING. You may weld the bumper and bumper shock there must be at least a 1“ gap between bumper and frame if using a factory bumper shock. Bumper may be welded directly to frame but the bumper shock must be removed completely. No adding metal. .1980 and NEWER bumpers only will be permitted. No tilting OR COLD BENDING of frames will be permitted
13. Hood- wire ONLY. 8 double strand of #9 wire 2 may go around bumper and or frame. Hoods must be open for inspection. (12" x 12" hole over carburetor). Deck lids may be wired same way no welding permitted.
14. Angles for cross member can't be longer than 5" and must be within 12" from factory location.
15. Tie Rods MAY BE REINFORCED No gas tank protectors.
16. Factory body bolts may be changed to ½” bolts you must use factory rubber and bushing spacer and there must be a 1 “ gap between body and frame. YOU MAY HAVE A BAR IN DASH AREA AND ONE BEHIND SEAT SHEET MEATAL TO SHEET METAL ONLY AND CAN NOT STENGTHEN CAR IN ANY WAY.
17. Rear coil springs may be wired or chained. No solid suspensions. All suspension components must remain factory stock. No modifications will be permitted. Cars must bounce.
18. Front coil springs must remain stock. You can use screw-in spacers. Leaf spring cars must remain factory springs. NO EXCEPTIONS! You cannot change coil spring to leaf spring set ups.
19. Car must set level bumpers can not be higher than 18” to bottom of bumper
20. Any stock 5 bolt rear end permitted. No rear end protectors. Must use STOCK trailing arms.
21. Cars must be stock.
22. WE HAVE THE RIGHT TO RE-INSPECT, CUT, OR DRILL ANY CAR AT ANY TIME. IF YOU ARE CAUGHT BREAKING THE RULES SET HERE FORTH YOU WILL FORFIET ANY AND ALL WINNINGS AND OR PRIZES YOU ARE DUE. .
23. NO OTHER MODIFICATIONS MAY BE MADE TO CAR UNLESS THEY ARE STATED IN THE RULES ABOVE IF YOU STRETCH A RULE YOU WILL LOSE THAT RULE.NO WELDS ON FRAME!